edmunster206
08-16-2007, 08:12 AM
Total CaptiveWorks how to.
Standard and Premium bin how to
Knowing that there are two CaptiveWorks 600 models
it is important that you put the rite bin in when
you set up your Set Top Box or better known as STB.
There are two STB's to deal with one being the 600S
and the other being the 600P. You must not use the
wrong bin in either one or you will seriuosly mess
up the TSOP and there is only one way to save them
after that and that is called "CLONING" and you don't
want to go there. I will mention cloning and the end
on this tutorial.
1. Power off the receiver from the back switch.
2. Hold the front panel power button and while holding turn on the back switch, receiver should display (boot)
3. open the 1.06 loader for the 600s and open the latest bin
for the 600s (standard) or the 1.07 loader and open the latest bin (premium).
4. Hit the start button and wait for the loader to cycle through the process
until you see the display read -END-.
5. Once you see this message power the STB off at the back and hook it up to
your TV via your usual setup. (cabling and what not)
6. After you have the STB hooked up it is time to scan in your channels, pending
on your setup weather it be one - two or three LNB's use this guide for
your satellite selection.
7. DISH and BEV LNB setups
Echostar 6,8 110.0W
LNB Power: On
LNB Type: Standard
LNB Freq.: 11250
22khz: Off
TP Freq.: 12224
Search Option: All
DiSEqC 1.0: Port 1
Motor: Off
Legacy SW: None
Echostar 7 119W
LNB Power: On
LNB Type: Standard
LNB Freq.: 11250
22khz: Off
TP Freq.: 12239
Search Option: All
DiSEqC 1.0: Port 2 (In most situations it's best to set LNB type to burst)
Motor: Off
Legacy SW: None
Nimiq 1,3 91.0W
LNB Power: On
LNB Type: Standard
LNB Freq.: 11250
22khz: Off
TP Freq.: 12224
Search Option: All
DiSEqC 1.0: Port 3
Motor: Off
Legacy SW: None
8. After you have scanned in what ever sat or sats you require it is time
to go to your setup menu and go to system selection and make sure you have
all your settings rite to move on to the next stage.
Press system settings and it will lead you to a new menu. Only worry about
these settings.
a. Auto roll - on
b. key message - on
next go over to EPG menu and make sure you have this setting
c. sid - on
d. return to the TV by exiting all menus till you see the scrambled channel message.
after that press "F1 000" and you will see the message "PATCH ENABLED"
After that sit back and watch TV.
9. Epilogue - in closing
If you follow this setup ritual you will have no problems with your CaptiveWorks
receivers and it will make you FTA experience an enjoyable one so make sure you
follow these simple rules and you should have no problems.
__________________________________________________ __________________________________
Cloning: This is a last resort.
12.How to Clone CW600s Box to Box?
=========================
From DigitalPlus:
1) Connect the master and slave box with twist RS232 null modem cable (pin2 to pin3, pin3 to pin2, pin5 to pin5).
2) Start the master receiver and press "POWER" key to make it standby ?- - : - -?.
3) Start the slave receiver, in the master box the led will display 'H' and blink it.
4) Input the password:
111 ---- Transfer S/W
222 ---- Transfer data
333 ---- Transfer data, then S/W
444 ---- Copy whole flash except Boot Loader.
5) After finishing inputting the password. Transfer will begin. When it finish, the LED will Display "-End". Disconnect the cable, start your receiver.
Note: By the different password, you can do what ever you want to do for Box to Box.
This should work with both 600S and 600P
Please take the time to learn the iner workings of your CaptiveWorks reciever
and don't try to veer from the path I have provided and you will have an enjoyable
experience with your CaptiveWorks Product. Cheers to all and I hope you all
appreciate the time I took to put this Sticky together.
Brought to you by FTA BROTHERHOOD
Standard and Premium bin how to
Knowing that there are two CaptiveWorks 600 models
it is important that you put the rite bin in when
you set up your Set Top Box or better known as STB.
There are two STB's to deal with one being the 600S
and the other being the 600P. You must not use the
wrong bin in either one or you will seriuosly mess
up the TSOP and there is only one way to save them
after that and that is called "CLONING" and you don't
want to go there. I will mention cloning and the end
on this tutorial.
1. Power off the receiver from the back switch.
2. Hold the front panel power button and while holding turn on the back switch, receiver should display (boot)
3. open the 1.06 loader for the 600s and open the latest bin
for the 600s (standard) or the 1.07 loader and open the latest bin (premium).
4. Hit the start button and wait for the loader to cycle through the process
until you see the display read -END-.
5. Once you see this message power the STB off at the back and hook it up to
your TV via your usual setup. (cabling and what not)
6. After you have the STB hooked up it is time to scan in your channels, pending
on your setup weather it be one - two or three LNB's use this guide for
your satellite selection.
7. DISH and BEV LNB setups
Echostar 6,8 110.0W
LNB Power: On
LNB Type: Standard
LNB Freq.: 11250
22khz: Off
TP Freq.: 12224
Search Option: All
DiSEqC 1.0: Port 1
Motor: Off
Legacy SW: None
Echostar 7 119W
LNB Power: On
LNB Type: Standard
LNB Freq.: 11250
22khz: Off
TP Freq.: 12239
Search Option: All
DiSEqC 1.0: Port 2 (In most situations it's best to set LNB type to burst)
Motor: Off
Legacy SW: None
Nimiq 1,3 91.0W
LNB Power: On
LNB Type: Standard
LNB Freq.: 11250
22khz: Off
TP Freq.: 12224
Search Option: All
DiSEqC 1.0: Port 3
Motor: Off
Legacy SW: None
8. After you have scanned in what ever sat or sats you require it is time
to go to your setup menu and go to system selection and make sure you have
all your settings rite to move on to the next stage.
Press system settings and it will lead you to a new menu. Only worry about
these settings.
a. Auto roll - on
b. key message - on
next go over to EPG menu and make sure you have this setting
c. sid - on
d. return to the TV by exiting all menus till you see the scrambled channel message.
after that press "F1 000" and you will see the message "PATCH ENABLED"
After that sit back and watch TV.
9. Epilogue - in closing
If you follow this setup ritual you will have no problems with your CaptiveWorks
receivers and it will make you FTA experience an enjoyable one so make sure you
follow these simple rules and you should have no problems.
__________________________________________________ __________________________________
Cloning: This is a last resort.
12.How to Clone CW600s Box to Box?
=========================
From DigitalPlus:
1) Connect the master and slave box with twist RS232 null modem cable (pin2 to pin3, pin3 to pin2, pin5 to pin5).
2) Start the master receiver and press "POWER" key to make it standby ?- - : - -?.
3) Start the slave receiver, in the master box the led will display 'H' and blink it.
4) Input the password:
111 ---- Transfer S/W
222 ---- Transfer data
333 ---- Transfer data, then S/W
444 ---- Copy whole flash except Boot Loader.
5) After finishing inputting the password. Transfer will begin. When it finish, the LED will Display "-End". Disconnect the cable, start your receiver.
Note: By the different password, you can do what ever you want to do for Box to Box.
This should work with both 600S and 600P
Please take the time to learn the iner workings of your CaptiveWorks reciever
and don't try to veer from the path I have provided and you will have an enjoyable
experience with your CaptiveWorks Product. Cheers to all and I hope you all
appreciate the time I took to put this Sticky together.
Brought to you by FTA BROTHERHOOD